• 800.878.8181

  • info@nhyates.com

Taco LOFlo System Sets a New Standard

taco LOFlo System

Taco LOFlo System from N.H. Yates

Designers and engineers are constantly looking for new ways to make heating and cooling systems more efficient and environmentally friendly. The people at Taco created their LOFlo System with the intention of setting a new standard in design and performance for a Green Energy hydronic regulator, and, they’ve done just that. The award-winning Taco LOFlo System is a hydronic heating and cooling regulator that significantly reduces the flow of water in hydronic heating and cooling systems. Typically used in radiant panel (ceiling, wall, or floor) and chilled beam (passive and active) applications, the Taco LOFlo System significantly reduces pump flows and pipe sizes which equates to reduced energy consumption and lower installation costs. In addition, the LOFlo System also allows for precise control of supply water to the terminal, and precise control of room temperatures.

How Does the Taco LOFlo System Work?

taco LOFlo System

The LOFlo System is a simple, factory-ready package that allows users to control each individual zone at the lowest possible flow rate by maintaining the highest possible water supply temperature when cooling and lowest temperatures when heating. The LOFlo unit consists of a single cast header which functions as a hydraulic separator with two small circulators attached. One of the circulators is for the primary system flow and the other injection circulator that adjusts to precisely match the required load on a given zone. After installation, in a modern radiant system or chilled beam system, only two pipes are needed to control and maximize the flow rate. Flow rates are able to be reduced without the use of control valves, balancing valves, or piping loses to overcome. Instead, one small, reliable circulator takes the place of all these components. The Taco LOFlo System automatically provides only the flow temperature of water needed to satisfy the zone load at any given time.

At N.H. Yates, we know water. If you are a designer or engineer looking for more information on the Taco LOFlo System contact a water professional at N.H. Yates today!

 

Dunkirk Condensing Gas Boilers

dunkirk condensing gas boilers

Dunkirk Condensing Gas Boilers from N.H. Yates

The people at Dunkirk are known by those in the HVAC and plumbing industries for delivering innovative, efficient and dependable heating products. At N.H. Yates, we are proud to represent the entire line of Dunkirk Gas Boilers. In this post, we will be focusing specifically on Dunkirk Condensing Gas Boilers. When choosing a condensing boiler, Dunkirk offers a variety of choices to meet a variety of needs. The most recent model of Dunkirk Condensing Boiler utilizes an innovative vertical mounted helical fin tube heat changer that boasts a 95% AFUE rating. In addition, these modulating sealed combustion boilers feature built-in Outdoor Temperature Rest that reduces heating costs. Here are a few of the most popular models of Dunkirk Condensing Gas Boilers.

Dunkirk Helix VLT

dunkirk condensing gas boilers

 

The Dunkirk VLT Condensing Gas Boiler is a wall hung unit that features built-in primary and secondary piping and a built-in low water cut off. The Helix VLT works on a 5:1 turn down ratio and is approved for PVC, CPVC, and polypropylene vent systems. And of course, the Helix VLT is low maintenance, and self-cleaning.

Dunkirk DCC/DCB High-Efficiency Wall Mounted Modulating Condensing Boiler

dunkirk condensing gas boilers

The Dunkirk DCC/DCB high-efficiency wall mounted modulating condensing boiler features AI Control Technology that automatically sets up the boiler during the initial setup and recognizes natural or LP gas with no conversion kit required. In addition, the AI Control system continuously monitors combustion and adjusts gas and air flow to optimize combustion and fuel savings. Both the DCC/DCB models have a 7:1 turn down modulation ratio in DHW mode and a 5:5:1 ratio in heating mode.

Dunkirk DMG 380 High-Efficiency Condensing Hot Water Boiler

dunkirk condensing gas boilers

The DMG 380 High-Efficiency Condensing Hot Water Boiler has a company floor standing design with an optional plug-and-play, CSD-1 kit available for the unit. In addition, the DMG 380 has a 10:5:1 modulation turn down ratio and a high-limit electronic ignition boiler control module. The unit also comes equipt with a digital temperature display with diagnostics and programmable settings.
Dunkirk Helix VX Vertical Laser Tube Wall Hung Stainless Steel Modulating Condensing Boiler

dunkirk condensing gas boilers

The Dunkirk Helix VX is the Rolls Royce of modulating condensing boilers. The Helix VX is a low maintenance, self-cleaning, heat exchanger and was designed to withstand up to 150 psi MAWP. In addition, this unit is approved for PVC, CPVC, and polypropylene venting and is rated Energy Star 2018 Most Efficient. Finally, the Helix VX comes with a 15-year limited manufactures warranty plus a first year $500 heat exchanger labor warranty.

At N.H. Yates, we know water. If you are a contractor or engineer interested in more information on Dunkirk Condensing Gas Boilers contact a water professional at Yates today!

 

Maxitrol Gas Combination Controls

Maxitrol Gas Combination Controls

Maxitrol Combination Controls from N.H. Yates!

Gas valves are used to regulate the flow of flammable gases to and from a boiler or other gas equipment. Redundant gas valves control the passage of gas to the burner in a gas furnace or other gas-fueled devices. The purpose of a redundant gas valve is to allow the pilot valve operator, or, the main valve operator to shut off the flow of gas to the main burner. This redundancy creates more options and allows opportunities to keep the gas from the burner whenever necessary. Maxitrol Combination Controls are perfect for use in many applications such as gas boilers, power burners, spa heaters, wall furnaces, gas fires, patio heaters, agricultural heaters, and commercial cooking appliances. In addition, these combination controls are suitable for natural, manufactured, mixed gases, liquefied petroleum gases, and LP gas-air mixtures. At N.H. Yates, we are proud representatives of the entire line of Maxitrol products, including the Maxitrol Combination Controls.

Models of Maxitrol Combination Controls

Maxitrol Combination Controls for gas equipment come in several models that are appropriate for different application and needs. Here is a brief outline of each model and their capabilities:

Maxitrol Combination Control Model CV100

Maxitrol Gas Combination Controls

The CV100 is a single solenoid shut-off valve with an integrated pressure regulator. This model gas regulator is used for applications with high capacity pilot lines such as gas boilers and power burners.

Maxitrol Combination Control Model CV200

Maxitrol Gas Combination Controls

The CV200 is a dual-solenoid shut-off valve with an integrated pressure regulator. The CV200 is a redundant combination control that is used in direct spark or hot surface ignition applications. This unit eliminates the need for a standing or continuous burning pilot flame. Some appropriate applications for the CV200 include direct vent gas-fired baseboard heaters, space heaters, wall furnaces, water heaters, gas fireplaces, and commercial cooking appliances.

Maxitrol Combination Control Model CV300

Maxitrol Gas Combination Controls

 

The CV300 is a dual solenoid shut-off valve with an integrated pressure regulator, however, an optional pressure regulated pilot gas outlet is available. Appropriate applications for the CV300 include gas fires, commercial cooking appliances, and patio heaters.

At N.H. Yates, we know water. If you are a contractor or engineer interested in more information on Maxitrol Gas Combination Control contact one our of water professionals today!

Flex-Hose Pumpsaver

flex-hose

Flex-Hose Pumpsaver from N.H. Yates

Many engineers and contractors use pump savers to prevent damage to pumps caused by piping stress that can shorten the life of the pump and its components. Rather than allowing hazardous movements and fluctuations, pump saver connectors absorb vibrations, accommodate for misalignments, and reduce the overall noise of pumping systems. The Flex-Hose Pumpsaver is the only one on the market that utilizes a closed pitch hose which makes for an unusually flexible, yet sturdy connection. This closed pitch construction saves installers during installation when aligning the piping system. In addition, the Pumpsaver’s innovative design saves many headaches for engineers during the design process.

Why Choose the Flex-Hose Pumpsaver?

flex-hose pumpsaver

At Flex-Hose Co., safety and performance are at the heart of everything they design. Each Pumpsaver produced by Flex-Hose Co. is made using the highest quality materials and manufactured under the strictest standards. In fact, Flex-Hose Co. only employes welders that are ASME Section IX certified to perform the complicated welds that are necessary to make the Pumpsaver. This attention to detail means that the Flex-Hose Pumpsaver will never come from the factory with any raw, jagged, or sharp edges which unfortunately are the industry norm. Instead, each Pumpsaver comes from the factory fit for a smooth transition at the first convolution flange. After completion, each Pumpsaver must pass a pressure test before they are sent to market. The Pumpsaver is available in stainless steels or bronze and is available in sizes 1/2 inch to 14 inches in diameter. Finally, the Pumpsaver is designed to be pressure tested up to 1.5X the maximum rated working pressure and are manufactured with a 4:1 safety factor. This compact design means you’ll save valuable space.

At N.H. Yates, we know water. If you are a contractor or engineers looking for more information on the Flex-Hose Pumpsaver contact a water professional at N.H. Yates today!

Maxitrol Gas Filters

maxitrol gas filters

Maxitrol Gas Filters Are Available From N.H. Yates

Maxitrol gas filters are fit for many applications including natural, manufactured, mixed gases, liquefied petroleum gases and LP gas/air mixture piping systems. The unique filter matting of Maxitrol Gas Filters is very effective at separating dust from circulating fuel. The wide filtering surface and depth of Maxitrol filters give them a remarkably high capacity for accumulated dust. In addition, Maxitrol’s super-fine mesh filter inserts will not allow particles larger than 0.05mm, or 50 microns, to flow through the filter. These filter inserts are replaceable and are quick and easy to change out and keep fuel as clean as possible. For installers and maintenance workers, the Maxitrol filter’s housing is compact and suitable for new equipment installation or retrofitting onto an older system.

Maxitrol Gas Filter Specs

The housings of all Maxiotrol Gas Filters are made of durable cast aluminum, while the filters themselves consist of a polypropylene impregnated fleece. The units are made with Rp or Rc thread (parallel or taper) dimensions according to ISO 7-1. National Pipe Taper (NPT) thread complies with ANSI standards. Maxitrol gas filters have a maximum operating inlet pressure of 15 psi and an ambient temperature limit of 175º F or 80º C.

Changes to the National Fire Prevention Association (NFPA) Standard 86 requires the installation of a gas filter or strainer on any new oven and/or furnace. In addition, all new filters must be tested according to DIN 3386 and meet DIN/DVGQ approval standards. However, all Maxitrol Gas Filters meet these standards and are approved for use in the US as well as most European countries.

Maxitrol Gas Filters are available in the following sizes and models:

maxitrol gas filters

At N.H. Yates, we know water. If you are a contractor or installer who would like more information on Maxitrol Gas Filters contact a water professional at N.H. Yates today!

Flex-Hose Bellowsflex Metal Bellows Expansion Joint

bellowsflex

Flex-Hose Bellowsflex Metal Bellows Expansion Joint

As many engineers know, the rotating parts of a pump produce vibrations that can become strong enough to pull fixtures out of the ceiling and damage property. To help prevent these powerful vibrations, one option that builders choose are stainless steel bellows pump connectors. At N.H. Yates we are proud to be a manufactures representative of Flex-Hose Bellowsflex Metal Bellows Expansion Joint. The Bellowsflex is an excellent choice for absorbing vibrations, compensating for misalignment at equipment connections and accommodating thermal growth in many service conditions and applications.

Why Choose the Bellowsflex from Flex-Hose?

bellowsflex

The standard Flex-Hose Bellowsfelx bellows element is manufactured with 321 stainless steel which is it not susceptible to corrosion or rust even after reaching temperatures up to 900º C or about 1,650º F. In addition to the 321 stainless steel, the Bellowfelx is available in other heat and corrosion resistant alloy materials for higher temperature applications. The Bellowflex comes from the factory with a standard pressure rating of up to 300 PSI. However, the maximum system test pressure is can be up to 1.5 times the working pressure. And of course, the Bellowflex can be equipt with accessories such as tie rods, limit rods, flow liners, and protective covers and/or shrouds. Finally, Flex-Hose offers the Bellowflex with multi-ply bellows for added flexibility and endurance. The reduced thickness of the individual bellow plies results in less bending due to the axial motion which increases the life of the bellows.

Bellowsflex comes in sizes 2 thru 60 inches in diameter and pressure ratings 50, 150, 300, and 600 PSI full vacuum service. In addition, plate flange, raised-face forge Slip-On Flange, Vanston “Floating” Flange, pipe weld ends.

At N.H. Yates, we know water. If you are a contractor or engineer that needs more information about the Bellowsflex from Flex-Hose, contact the water professionals at N.H. Yates today!

Maxitrol Ball Valves

maxitrol ball valves

Maxitrol Ball Valves from N.H. Yates

Ball valves guide, direct, and modulate the flow of various types of liquids by way of an opening which has a small opening in the middle called a port. By turning the handle on the ball valve, the port manually opens and closes to control the pressure of the liquid. Plumbing and HVAC contractors use ball valves to control the flow of many substances including water, oil, steam, and gas on a variety of applications. At N.H. Yates we are proud to be a manufactures representative for the entire line of Maxitrol Ball Valves which feature their innovative hollow ball and seat design. The research and development team at Maxitrol put years of work and testing into their ball valves to manufacture the hollow ball with a technical level not found in other products.

Maxitrol Ball Valves Models BV602 & BV250

The BV602 and BV250 Ball Valves from Maxitrol have a strong body of forged brass, female NPT inlet and outlet, hard chrome plated ball, and anticorrosion Dactomet treated handle. The BV602 contains seats of Buna N, and are of one-piece construction. Whereas the BV250 model contains PTFE and is made of two-piece construction. Both Maxitrol Ball Valves are equipped with a self-locking nut that improves reliability between the stem and lever by providing additional stability from vibrations. In addition, to the seal created by the O-ring, a PTFE anti-thrust washer seals against the shoulder of the valve. Maxitrol manufactures both models of ball valves with a unique new seat shape to reduce friction during opening and closing. This seat shape reduces torque on the entire unit by 20% to 40% which increases the life of the ball valve.

At N.H. Yates, we know water. If you are interested in more information on Maxitrol Ball Valves contact one of the water professionals at Yates today!

Holdrite ProGuard PEX Stub Out

Holdrite ProGuard PEX Stub Out

Get the Holdrite ProGuard PEX Stub Out from N.H. Yates

As most plumbing contractors already know PEX tubing offers several benefits over traditional copper piping. First, PEX piping’s flexibility, along with its ability to easily be cut to custom sizes, reduce the need for most elbows and joints during installation. Second, PEX pipes won’t sweat in high humidity conditions, and, is resistant to bursting, even if the line freezes solid. And finally, it’s easy to make custom joints using PEX piping. All you need is a special crimping tool to secure the metal rings to the barbed fitting. For more than 15 years, the folks at Holdrite have been at the forefront of the PEX revolution. At N.H. Yates, we are proud to represent the Holdrite ProGuard PEX Stub Out support, an integral piece of any PEX piping system.

Why Choose the Holdrite ProGuard PEX Stub Out?

Holdrite ProGuard PEX Stub Out

The most important reason to choose the Holdrite ProGuard PEX Stub Out is its unparalleled ability to prevent extreme turning that can cause the PEX to kink. With the ProGuard Stub Out, your PEX will have a 360-degree turning radius so flow can continue without impediment. In addition, the ProGuard Stub Out eliminates the need for concealed joints and costly fittings that can cause leaks and provides protection by ensuring everything remains inside the wall envelope. Last, the Holdrite ProGuard PEX Stub Out is compatible with all PEX manufactures tubing and integrates directly with #SB3 and #SB4 Holdrite Stout Brackets.

Take a look at this informative video to find out what makes the ProGuard PEX Stub Out a flexible and reliable component for any solid stub out support solution.

At N.H. Yates, we know water. If you are a contractor with interest in the Holdrite ProGuard PEX Stub Out contact the water professionals at N.H. Yates today.

Flex-Hose Flexcomp Expansion Compensators

Flexcomp Expansion Compensators

 

Flex-Hose Flexcomp Expansion Compensators

At N.H. Yates, we proudly represent the complete line of Flex-Hose Expansion Compensators including the innovative Flexcomp Expansion Compensator. The people at Flex-Hose engineer and manufacture the Flexcomp for a broad range of requirements including some of the most demanding applications in the world. Flexcomp Expansion Compensators are designed to absorb thermal growth in HVAC small diameter piping systems. In most cases, these expansion compensators eliminate the need for expensive pipe loops and the associated maintenance associated with packed slip joints. In addition, Flex-Hose fabricates the Flexcomp from stainless steel and is available with copper tube ends, steel male NPT ends, or 150 lb steel flanges. The Flexcomp is available for pipe ranging from 3/4 inch to 4 inches in diameter and pressure rating up to 175 PSI.

Why Choose Flexcomp Expansion Compensators?

Flexcomp Expansion Compensators

First, Flex-Hose understands that no contractors requirements will be exactly the same and therefore design the Flexcomp to work with a wide variety of applications. Second, the Flexcomp Expansion Compensator’s compact design allows contractors to save valuable space when installing HVAC systems. The Flexcomp is able to absorb up to 2 inches of axial movement resulting from thermal growth in domestic hot water, heating hot water, and chilled piping systems. Third, the Flexcomp is durable. The entire unit is externally pressurized and made of rugged stainless steel bellows to assure safety and reliability. Finally, the Flexcomp is an energy efficient choice. The unit’s liner design prevents bellows impingement or fatigue due to flow reduced vibration. The standard working pressure ratings are sufficient for up to 200 psi with a maximum system test pressure of 300 psi.

Flexcomp Expansion Compensators

 

At N.H. Yates, we know water. If you are a contractor in need of more information on Flex-Hose Flexcomp Expansion Compensators or any other Flex-Hose product, contact a water professional at Yates today!